Kyocera Mita/Taskalfa/Copystar Error Codes

Kyocera Mita/Taskalfa/Copystar Copiers and printers are equipped with a self diagnostic function. When a problem is detected, copying is disabled. “C” and a number between 0100 and 7810 alternates, indicating the nature of the problem. Kyocera errors are of three types. Some of them can be reset by turning the machine power switch off and back on while some others activate “partial operation control” disabling the defective part/area of the machine (paper feed cassette, stapler, document processor etc). If a specific unit is not working, perform U906 after taking measures against the cause of trouble to reactivate the unit.
Fixing error codes (C6xxx series) must be reset by a technician after clearing the cause of trouble. Reseting a fixing code without proper repair may result in fire or damage. (See how to reset fixing errors).
A general purpose error code list is given below. Use “Ctrl + F” to easily find your desired error explanation.

Error CodeDescription
C0030Fax PWB Problem. Processing with fax software is disabled due to software or hardware issues.
C0060Main PWB Type Mismatch Error.
C0070Fax PWB Incompatability Detection Problem. Fax software is not compatible with main PWB software.
C0130Main PWB EEPROM Backup Memory Device Problem. EEPROM can not be written or read.
C0140Main PWB EEPROM Backup Memory Data Problem. Abnormal reading data from EEPROM.
C0150Engine PWB EEPROM Backup Memory Device Problem. EEPROM cannot be written or read.
C0160Engine PWB EEPROM Backup Memory Data Problem. Abnormal reading data from EEPROM. Read & write data do not match five times consecutively.
C0170Copy Counts Problem. A checksum error is detected in the main and engine backup memories for copy counters.
C0180Machine Number Mismatch Error. Machine number does not match on main and engine PWBs
C0600Main PWB DIMM Installed Incorrectly.
C0610Main PWB DIMM error
C0630DMA transmission of compressed, decompressed, rotated, relocated, or blanked-out image data does not complete within a specified period of time.
C0640Hard Disk Drive cannot be accessed
C0700Optional CF backup is not suitable.
C0800Image processing problem. JAM05 is detected twice.
C0830Fax Flash ROM program area checksum error
C0870Fax PWB to Main PWB high capacity data transfer problem.
C0880Fax PWB program archive problem.
C0920Fax backup data is not retained.
C1010Cassette #1 Lift Motor error. Exceeds 12 seconds of operation or 500ms of overcurrent.
C1020Cassette #2 Lift Motor error. Exceeds 12 seconds of operation or 500ms of overcurrent.
C1030PF-700 optional cassette #3 lift motor error.
C1040PF-700 optional cassette #4 lift motor error.
C1100PF-750 (Left) Lift Motor 1 error. Exceeds 1 second overcurrent.
C1110PF-750 (Right) Lift Motor 2 error. Exceeds 1 second overcurrent.
C1120PF-750 (Left) Lift Motor 1 position problem. PF switch 2 remains off after 30 seconds of motor operation.
C1130PF-750 (Right) Lift Motor 2 position problem. PF switch 1 remains off after 30 seconds of motor operation.
C1800PF-700/PF-750 Communication Problem.
C1900PF-700 EEPROM error. Write data & Read data are not in agreement three times consecutively.
C2000Drive Motor Problem. Stable Off is detected exceeding 1 sec after motor stability. Stabilization is not detected with 6 sec of activation.
C2250Main Charge Cleaner Motor error. Lock error is detected three times in a row during cleaner motor operation.
C2500Paper Feed Motor error. Stable Off is detected exceeding 1 sec after motor stability. Stabilization is not detected within 6 seconds of activation.
C2600PF-700 Drive Motor error. Lock signal exceeds 500ms.
C2600PF-750 Paper Conveying Motor error. Lock signal exceeds 450ms.
C3100Scanner Carriage Problem. Scanner home position is not detected at initialization or start of copying from contact glass.
C3200Exposure Lamp Problem. Exposure lamp does not reach the input value threshold within 5 sec of commencing reading.
C3210Exposure Lamp Problem. Exposure lamp does not exceed the input threshold value within 5 sec of commencing reading.
C3300CCD AGC Problem. After AGC correct input is not obtained at the CCD.
C3310CIS AGC Problem. After AGC correct input is not obtained at the CIS.
C3500Communication Error Between Scanner and SHD.
C3900Scanner PWB Backup Memory Read/Write Problem. Read & Write data does not match.
C3910Scanner PWB Backup Memory Data Problem. Data in a specified area of the backup memory does not match the specified values.
C4000Polygon Motor Synchronization Problem. Polygon motor does not stabilize speed within 20 sec of activation.
C4010Polygon Motor Steady-State Problem. Stable Off is detected for 20 sec continuously after polygon motor stabilization.
C4200BD Steady-State Problem. ASIC detects a Beam Detect error A for 2 sec after polygon motor stabilization.
C5300Cleaning Lamp Broken Wire. While the cleaning lamp is On, the broken wire detection signal is detected for 2 sec continuously.
C6000Fuser Heater Break. Thermistor1 detected less than 70C/158F for 10 sec during warmup & ready. Thermistor2 detected less than 40C/104F for 10 sec during warmup & ready. Temp at thermistor 1or 2 does not rise by at least 1C/1.8F within 5 sec.
C6020Abnormally High Thermistor Temperature. Thermistor 1 or 2 is detected 250C/482F for 40ms or more.
C6030Fixing Thermistor Break Error. Thermistor break signal is detected for 1 sec.
C6050Abnormally Low Thermistor Temperature. Thermistor 1 is detected 80C/176F or less for 1 sec continuously during copying.
C6400Zero-Cross Signal Error. While fuser heater On/Off control is performed, the zero-cross signal is not input within 3 sec.
C6410Fuser Unit Connection Insertion Problem. Absence of fuser unit is detected.
C6420Fuser Unit Fuse Cut Problem. The fuse has been cut 33 sec after the fuse cut signal is turned on.
C7300Toner Container Problem. Toner level is not detected when toner empty is detected.
C7400Developing Unit Connection Insertion Problem. Absence of the developing unit is detected.
C7410Drum Unit Connection Insertion Problem. Absence of the drum unit is detected.
C7800Broken External Thermistor Wire. Thermistor on the environmental sensor outputs 4.5v or more.
C7810Short-Circuited External Thermistor. Thermistor input value is 0.5v or less.
C7900Drum EEPROM Error. Reading or writing to the EEPROM cannot be performed.
C7910Developing EEPROM Error. Reading or writing to the EEPROM cannot be performed.
C8020DF-710 Punch Motor Problem. Punch motor lock signal is detected for 500ms or more during activation.
C8030DF-730 Tray Upper Limit Detection Problem. When tray elevation motor raises a tray, the upper limit switch detects On condition.
C8050DF-710 Paper Conveying Belt Motor 1 Error. Paper conveying belt home position sensor 1 does not turn Off within 1.5 sec. Paper conveying belt home position sensor 1 does not turn On within 2.5 sec. Jam 88.
C8060DF-710 Paper Conveying Belt Motor 2 Error. Paper conveying belt home position sensor 2 does not turn Off within 1.5 sec. Paper conveying belt home position sensor 2 does not turn On within 2.5 sec.
C8070DF-710 Internal Tray Communication Error. The connection is detected, but communication is not possible with the internal tray.
C8140DF-710 Main Tray Problem. Main tray is not detected in not detected by main tray top limit detection sensor or main tray capacity detection sensor within 20 sec of ascending. Main tray upper limit detection sensor or main tray load detection sensor is not detected as Off within 20 sec of main tray descending. Main tray lower limit detection sensor is not detected as On within 20 sec of main tray descending. Main tray upper limit detection sensor or main tray load detection sensor remain on for 2 sec or more during main tray ascent.
C8140DF-730 Tray Elevation Motor Problem. Tray lower limit sensor or surface view sensor cannot be detected within 10 sec.
C8170DF-710 Side Registration Motor 1 Problem. During initial rotations home position is not detected within 3 sec. Jam 88.
C8170DF-720 Front Side Registration Motor Problem. During initial rotations home position is not detected within 106 pulses. When the front side home position sensor is turned off during initialization, the sensor did not turn on within 3 sec.
C8170DF-730 Adjustment Motor Problem. Adjustment motor home position motor is not detected within a specific time during activation.
C8180DF-710 Side Registration Motor 2 Problem. During initial rotations home position is not detected within 3 sec. Jam 88.
C8180DF-720 Rear Side Registration Motor Problem. During initial rotations home position is not detected within 106 pulses. When the rear side home position sensor is turned off during initialization, the sensor did not turn on within 3 sec.
C8190DF-720 Trailing Edge Registration Motor Problem. During initial rotations home position is not detected within 106 pulses. When the trailing edge home position sensor is turned off during initialization, the sensor did not turn on within 3 sec.
C8210DF-710 Stapler Moving Motor 1 Error. During initial rotations home position is not detected within 1.5 sec.
C8210DF-720 Finisher Stapler Problem. Stapler home position sensor does not change state from non-detect to detect within 200ms of forward (CCW) rotation. During initial rotations stapler home position detection does not change state from non-detect to detect within 600ms of reverse (CW) rotation.
C8210DF-730 Stapler Problem. Home position is not detected within a specific time of activation.
C8220DF-710 Stapler Moving Motor 2 Error. During initial rotations home position is not detected within 3.5 sec.
C8230DF-710 Stapler Motor Problem. Jam 82 is indicated.
C8300BF-710 Centerfold Unit Communiation Error. Although the connection is detected, communication is not possible with the centerfold unit.
C8310BF-710 Centerfold Side Registration Motor 1 Problem. During initial rotations home position is not detected within 1000ms.
C8320BF-710 Centerfold Paper Conveying Belt Motor Problem. During initial rotations home position is not detected within 2500ms.
C8330BF-710 Blade Motor Problem. During initial rotations home position is not detected within 1500ms.
C8340BF-710 Centerfold Staple Motor Problem. Jam 89.
C8350BF-710 Centerfold Side Registration Motor 2 Problem. During initial rotations home position is not detected within 1000ms.
C8360BF-710 Centerfold Main Motor Problem. The motor lock signal is detected for more than 1000ms during activation.
C8440DF-730 Sensor Adjusting Problem. The paper entry sensor cannot be adjusted within the specified range.
C8460DF-730 EEPROM Problem. Reading to or writing from EEPROM cannot be performed.
C8500MT-710 Communication Error. The connection is detected, but communication is not possible with the mailbox.
C8510MT-710 Drive Motor Problem. The motor lock signal is detected for more than 500ms during activation.
C8800DF-710 Communication Problem. No communication: there is no reply after (5) tries. Abnormal communication: a parity or checksum error is detected (5) times in succession.
C8900DF-710 Backup Memory Data Problem. Read and write data does not match.
C8910PH-5A Backup Memory Data Problem. Read and write data does not match.
C8920MT-710 Backup Memory Data Problem. Read and write data does not match.
C8930BF-710 Backup Memory Data Problem. Read and write data does not match.
C9000DP-700 Communication Problem. A communication error is detected.
C9040DP-700 Lift Motor Ascent Error. The DP lift upper limit switch is not detected within 10000 pulses. After a one time retry, the DP lift upper limit switch could not be turned On.
C9050DP-700 Lift Motor Descent Error. The DP lift lower limit switch is not detected within 10000 pulses. After a one time retry, the DP lift lower limit switch could not be turned On.
C9060DP-700 EEPROM Error. Read and write data does not match. Data in the specified area of the backup memory does not match the specified values.
C9070DP-700 Communication Error between the DP and SHD. A communication error is detected.
C9080DP-700 Communication Error between the DP and CIS. Reading cannot be performed correctly.
CF000Operation Panel PWB Communication Error/System Error. Unknown error. Communication error between panel and main controller. (If CF620 occurred and is left, CF000 also occurred because of timeout control.
CF010Main PWB Checksum Error/System Error. Communication error between panel and main controller.
CF020Memory Checksum Error/Operation System Error.
CF030Main PWB System Error.
CF040Engine PWB Communication Error.
CF041Scanner PWB Communication Error.
CF050Engine ROM Checksum Error.
CF060Engine RAM Error.
CF070Flash ROM Error. Defective flash ROM (which?).
CF080Flash ROM Error (during download). Defective flash ROM (which?).
CF090Fax System M Communication Error.
CF14FPower Source Secondary Side Error/Operation System Error. The operation decomes unstable after recovering the power supply fail (brownout or power drop). Wall voltage is unstable or the main power supply switch was turned OFF/ON within 1 sec.
CF256Fax System M IOBL error or KUIOLIB error. Poor contact at the fax card card due to mis-installation.
CF257Fax System M IOBL error or KUIOLIB error. Poor contact at the fax card card due to mis-installation.
CF26FPrint System Other Errors. Bug of v.2.03B has been fixed by v. 2.04A (Booklet > Booklet Print).
CF3xxUndefined.
CF423Fax System M Error. Wrong data or value detected when the following function is used. Or poor contact at fax card due to mis-installation.
CF423Fax System M Error. The IF error detects during system authentication from ACT_Account_Manager. Or poor contact at fax card due to mis-installation.
CF433 CF434 CF437 CF43F CF441 CF444 CF445 CF451HDD Image Process Error. Destruction of stored jobs on the HDD. It may occur when selecting the keys for calling stored copy or scanner job from a custom box.
CF45F CF453 CF454 CF45F CF460 CF463 CF46F CF470HDD Image Process Error. Destruction of stored jobs on the HDD. It may occur when selecting the keys for calling stored copy or scanner job from a custom box.
CF473 CF47F CF484 CF487 CF48F CF490 CF493 CF494HDD Image Process Error. Destruction of stored jobs on the HDD. It may occur when selecting the keys for calling stored copy or scanner job from a custom box.
CF5xxUndefined.
CF610System Start Error.
CF620System Error. Error acquiring the event data. Panel detects CF000 as same error.
CF620System Error. Error acquiring the event data. Panel detects CF000 as same error. Unable to Load Files To CF Card.
CF7D7Readout Error of SSL (authentication data).
CFAxxHDD Error.
CFB2C CFB30 CFB31Panel Error. NetFont error. Communication error between panel and main controller during initialization or rejection of communication by controller during initialization. Blue Screen of Death.
CFB30Incompatible Level Of Firmware on Main EEPROM.
CFB31Corrupt Firmware on Main EEPROM.
CFB32Panel Error. Timeout request for start up command. Start command hasn’t been received. Possible destruction of system file in HDD. Cannot enter maintenance mode. Blue Screen of Death.
CFB33Panel Error. Detects disconnection with controller. Possible overdrive of control board or destruction of system file in HDD. Cannot enter maintenance mode. Blue Screen of Death.
F000Operation Panel PWB Communication Error.
F010Main PWB Checksum Error.
F020Memory Checksum Error.
F030Main PWB System Error.
F040Engine PWB Communication Error.
F041Scanner PWB Communication Error.
F050Engine ROM Checksum Error.
F060Engine RAM Error.
F070Flash ROM Error.
F080Flash ROM Error (during download).
F090Fax Control PWB Communication Error.
F14FPower Source PWB Second Side Error.
E00000 or U00000Fax Communication Error: No response or line busy after the set number of redials.
E00100 or U00100Fax Communication Error: Transmission was interruped by a press of the Stop/Clear key.
E00200 or U00200Fax Communication Error: Reception was interrupted by a press of the Stop/Clear key.
E00300 or U00300Fax Communication Error: Recording paper on the destination unit has run out during reception.
E00420 or U00420Fax Communication Error: A relay request was received from the host center but interrupted because of a mismatch in permit ID or telephone number.
E00421 or U00421Fax Communication Error: Subaddress-based relay reception was interrupted because of a mismatch in the specified subaddress relay box number.
E00430 or U00430Fax Communication Error: Polling request (confidential or reverse polling) was received but interrupted because of a mismatch in the permit number.
E00430 or U00430Fax Communication Error: Subaddress-based bulletin board transmission was interrupted because of a mismatch in the permit ID of the transmitting unit.
E00431 or U00431Fax Communication Error: Confidential polling transmission was interrupted because the specified confidential box number was not registered.
E00431 or U00431Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because the specified subaddress confidential box was not registered.
E00432 or U00432Fax Communication Error: Confidential polling transmission was interrupted because of a mismatch in the confidential box ID number.
E00432 or U00432Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because of a mismatch in the subaddress confidential box number.
E00433 or U00433Fax Communication Error: Confidential polling request was received but data was not present in the confidential box.
E00433 or U00433Fax Communication Error: Subaddress-based bulletin board transmission request was received but data was not present in the subaddress confidential box.
E00434 or U00434Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box number was intended for encryption.
E00435 or U00435Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box was being accessed.
E00435 or U00435Fax Communication Error: Subaddress-based bulletin board transmission request was received but interrupted because the specific subaddress confidential box was being accessed.
E00440 or U00440Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was not registered.
E00440 or U00440Fax Communication Error: Subaddress-based confidential reception or subaddress-based relay reception was interrupted because the specific subaddress box was not registered.
E00440 or U00440Fax Communication Error: Subaddress-based confidential reception or subaddress-based relay command reception was interrupted because the specific subaddress box number was being accessed.
E00441 or U00441Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was intended for encryption.
E00450 or U00450Fax Communication Error: The destination transmitter disconnected because the permit IDs did not agree while the destination transitter is in password-check transmission or restricted transmission.
E00460 or U00460Fax Communication Error: Encrypted reception was interrupted because the specified encryption box number was not registered.
E00460 or U00460Fax Communication Error: Ecrypted reception request was received but interrupted because the specified encryption box was being accessed.
E00462 or U00462Fax Communication Error: Ecryption reception was interrupted because the encryption key for the specified encryption box was not registered.
E00500 or U00500Fax Communication Error: Multiple communication was interrupted and the call was not made on destination units after interruption.
E00600 or U00600Fax Communication Error: The document processor cover is open.
E00601 or U00601Fax Communication Error: Document jam or the document length exceeds the maximum.
E00602 or U00602Fax Communication Error: Image scanning section problem
E00603 or U00603Fax Communication Error: No document feed.
E00604 or U00604Fax Communication Error: Document length exceeded the limit of the bitmap memory capacity.
E00610 or U00610Fax Communication Error: Recording section cover open.
E00611 or U00611Fax Communication Error: Recording paper jam.
E00613 or U00613Fax Communication Error: Image writing section problem.
E00614 or U00614Fax Communication Error: Nearly empty of recording paper.
E00615 or U00615Fax Communication Error: Empty of recording paper.
E00620 or U00620Fax Communication Error: Copier fixing unit problem.
E00622 or U00622Fax Communication Error: Copier drive motor problem.
E00655 or U00655Fax Communication Error: CTS was not activated after RTS due to a modem error.
E00656 or U00656Fax Communication Error: Data was not transmitted after CTS was activated due to a modem error.
E00670 or U00670Fax Communication Error: Power was cut off during communication.
E00677 or U00677Fax Communication Error: There was no file to transmit in the memory transmission mode.
E00690 or U00690Fax Communication Error: System error.
E00700 or U00700Fax Communication Error: Communication was interrupted because of a problem in the destination unit.
E00800 or U00800Fax Communication Error: A page transmission error occurred in G3 mode, because of reception of a RTN or PIN signal.
E00810 or U00810Fax Communication Error: A page transmission error re-occurred in G3 mode after retry of transmission in ECM mode.
E00900 or U00900Fax Communication Error: A page reception error occurred in G3 mode. An RTN or PIN signal was transmitted because of a page reception error.
E00910 or U00910Fax Communication Error: A page reception error occurred in G3 mode. A page reception error remained after retry of transmission in ECM mode.
E01000 or U01000Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An FTT signal was received for a set number of times after TCF signal transmissions at 2400bps.
E01000 or U01000Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An RTN signal was received in response to a Q signal (excluding EOP) after transmission at 2400bps.
E01001 or U01001Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. The function of the unit differs from that indicated by a DIS signal.
E01010 or U01010Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DNL (MPS or EOM) signal, and the preset number of command retransfers was exceeded (between units of our make).
E01011 or U01011Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DCS, TCF signal, and the preset number of command retransfers was exceeded.
E01012 or U01012Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS1, NSS2 (TCF) signal, and the preset number of command retransfers was exceeded (between units of our make).
E01013 or U01013Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS3, TCF signal, and the preset number of command retransfers was exceeded (between units of our make).
E01014 or U01014Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an MPS signal, and the preset number of command retransfers was exceeded.
E01015 or U01015Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOM signal, and the preset number of command retransfers was exceeded.
E01016 or U01016Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An MCF signal was received but no DIS signal was received after transmission of an EOM signal, and T1 timeout was detected.
E01017 or U01017Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOP signal, and the preset number of command retransfers was exceeded.
E01018 or U01018Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PRI-EOP signal, and the preset number of command retransfers was exceeded.
E01019 or U01019Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CNC signal, and the preset number of command retransfers was exceeded (between units of our make).
E01020 or U01020Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CTC signal, and the preset number of command retransfers was exceeded (ECM).
E01021 or U01021Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOR.Q signal, and the preset number of command retransfers was exceeded (ECM).
E01022 or U01022Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a RR signal, and the preset number of command retransfers was exceeded (ECM).
E01023 or U01023Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PS.NULL signal, and the preset number of command retransfers was exceeded (ECM).
E01024 or U01024Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.MPS signal, and the preset number of command retransfers was exceeded (ECM).
E01025 or U01025Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOM signal, and the preset number of command retransfers was exceeded (ECM).
E01026 or U01026Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOP signal, and the preset number of command retransfers was exceeded (ECM).
E01027 or U01027Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.PRI-EOP signal, and the preset number of command retransfers was exceeded (ECM).
E01028 or U01028Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. T5 timeout was detected during ECM Transmission (ECM).
E01040 or U01040Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received during standby for DIS signal reception.
E01041 or U01041Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DNL (MPS or EOM) signal (between units of our make).
E01042 or U01042Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS, TCF signal.
E01043 or U01043Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS1, NSS2 (TCF) signal (between units of our make).
E01044 or U01044Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS3, TCF signal (between units of our make).
E01045 or U01045Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an MPS signal.
E01046 or U01046Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOM signal.
E01047 or U01047Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOP signal.
E01048 or U01048Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PRI-EOP signal.
E01049 or U01049Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CNC signal (between units of our make).
E01050 or U01050Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTC signal (ECM).
E01051 or U01051Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an EOR.Q signal (ECM).
E01052 or U01052Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RR signal (ECM).
E01053 or U01053Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.NULL signal (ECM).
E01054 or U01054Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.MPS signal (ECM).
E01055 or U01055Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOM signal (ECM).
E01056 or U01056Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOP signal (ECM).
E01057 or U01057Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.PRI-EOP signal (ECM).
E01070 or U01070Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during handshake.
E01071 or U01071Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during message transmission.
E01072 or U01072Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A break in loop current was detected during transmission.
E01073 or U01073Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the receiver unit, a CM signal was not detected when transmitting after reception.
E01080 or U01080Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A PIP signal was received after transmission of a PPS.NULL signal.
E01091 or U01091Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because a PPR signal was received over (10) times even after reducing the communication speed to the minimum with the symbol speed maintained at the level of connection.
E01092 or U01092Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because of an impossible combination of the symbol speed and communication speed.
E01100 or U01100Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit differs from that indicated by a DCS signal.
E01101 or U01101Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit (excl. communication mode select) differs from that indicated by an NSS signal.
E01102 or U01102Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DTC (NSC) signal was received when no transmission data was in the unit.
E01110 or U01110Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DIS signal.
E01111 or U01111Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DTC (NSC) signal.
E01112 or U01112Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No training reception after reception of a DCS or NSS signal.
E01113 or U01113Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an FTT signal.
E01114 or U01114Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CFR signal.
E01115 or U01115Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an MCF signal.
E01116 or U01116Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a PPR signal.
E01117 or U01117Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CTR signal.
E01118 or U01118Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an ERR signal.
E01119 or U01119Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No further signals were received after reception of a message.
E01120 or U01120Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an MCF signal.
E01121 or U01121Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTP signal.
E01122 or U01122Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTN signal.
E01123 or U01123Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIP signal.
E01124 or U01124Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIN signal.
E01125 or U01125Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a CNS signal (between units of our make).
E01126 or U01126Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PPR signal (ECM).
E01127 or U01127Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an ERR signal (ECM).
E01128 or U01128Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RNR signal (ECM).
E01129 or U01129Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an SPA signal (short protocol).
E01140 or U01140Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DIS signal.
E01141 or U01141Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DTC signal.
E01142 or U01142Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS or NSS signal.
E01143 or U01143Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an FTT signal.
E01144 or U01144Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CFR signal.
E01145 or U01145Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after reception of a message.
E01146 or U01146Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an MCF signal (interoffice communication after reception of an MPS, EOM signal or confidential interoffice communication).
E01147 or U01147Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTP signal.
E01148 or U01148Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTN signal.
E01149 or U01149Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIPsignal.
E01150 or U01150Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIN signal.
E01151 or U01151Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPR signal (ECM).
E01152 or U01152Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTR signal (ECM).
E01153 or U01153Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an ERR signal (ECM).
E01154 or U01154Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an PNP signal (ECM).
E01155 or U01155Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an SPA signal (short protocol).
E01160 or U01160Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During message reception, transmission time exceeded the maximum transmission time per line.
E01161 or U01161Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Number of error lines exceeded limits during message reception.
E01162 or U01162Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A break in loop current was detected during message reception.
E01163 or U01163Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Polarity reversal was detected during message reception.
E01164 or U01164Fax Communication Error: Reception in G3 mode was interrupted by a signal error. One page length exceeded the specified length during message reception.
E01170 or U01170Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A decoding error occurred during MMR message reception.
E01172 or U01172Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the transmitting unit, a JM signal was not detected after transmission of a CM signal when receiving after transmission.
E01191 or U01191Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Communication was interrupted because an error occurred during an image data reception sequence in the V.34 mode.
E01199 or U01199Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DIS signal with different FIF was received after transmission of a DIS signal.
E01400 or U01400Fax Communication Error: An invalid one-touch key was specified during communication.
E01500 or U01500Fax Communication Error: A communication error occurred when calling in V.8 mode.
E01600 or U01600Fax Communication Error: A communication error occurred when called in V.8 mode.
E01700 or U01700Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary channel equivalent device training), before starting T.30 protocol, during transmission in V.34 mode. For example: INFO0/A/Abar (B/Bbar, for polling transmission)/INFOh was not detected.
E01720 or U01720Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in the period after initiating the control channel, before starting T.30 protocol, during transmission in V.34 mode. For example: PPh/ALT/MPh/E was not detected.
E01721 or U01721Fax Communication Error: A communication error occurred before starting T.30 protocol during transmission in V.34 mode. Operation was interrupted due to the absence of a common communication speed between the units. 1) A DCN signal was received from the destination unit and the line was cut, or 2) a DIS (NSF, CSI) signal was received from the destination unit and in response to the signal, the unit transmitted a DCN signal and the line was cut.
E01800 or U01800Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: INFO0/B/Bbar (A/Abar, for polling reception)/probing tone was not detected.
E01810 or U01810Fax Communication Error: A communication error occurred in phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: S/Sbar/PP/TRN was not detected.
E01820 or U01820Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in the period after initiating the control channel, before starting T.30 protocol during reception in V.34 mode. For example: PPh/ALT/MPh/E was not detected.
E02000 or U02000Fax Communication Error: Relay broadcast was refused by a relay station because of a mismatch in permit ID number and permit telephone number when a relay command was used.
E02100 or U02100Fax Communication Error: A relay command failed because the destination unit (relay station) had no relay broadcast capability.
E02200 or U02200Fax Communication Error: A relay command from a command station failed because a telephone number was not registered in the relay station was specified.
E02200 or U02200Fax Communication Error: Relay broadcast was requested to a relay station but failed because a telephone number was not registered in the relay station was specified.
E02200 or U02200Fax Communication Error: Subaddress-based relay broadcast transmission failed because the data registered in the subaddress relay box was deleted.
E02303 or U02303Fax Communication Error: Receiving station information was not normally received in reception of a relay command. Timeout was detected before a correct DNL signal was received.
E02304 or U02304Fax Communication Error: Receiving station information was not normally received in reception of a relay command. A signal other than MPS or EOM signal was received after a DNL signal was received.
E02400 or U02400Fax Communication Error: An interoffice subaddress-based relay transmission was interrupted because of a mismatch in the specified relay box number.
E03000 or U03000Fax Communication Error: No document was present in the destination unit when polling reception started.
E03100 or U03100Fax Communication Error: In reverse polling, although no original was set in the destination unit, transmission was complete.
E03200 or U03200Fax Communication Error: In confidential polling reception, data was not accumulated in the specified box in the destination unit.
E03200 or U03200Fax Communication Error: In interoffice subaddress-based bulletin board reception, data was not stored in the box specified by the destination unit.
E03300 or U03300Fax Communication Error: In polling reception from a unit of our make, operation was interrupted due to a mismatch in permit ID number or telephone number.
E03300 or U03300Fax Communication Error: In interoffice subaddress-based bulletin board reception, operation was interrupted due to a mismatch in permit ID number or telephone number.
E03400 or U03400Fax Communication Error: Polling reception was interupted because of a mismatch in individual numbers.
E03500 or U03500Fax Communication Error: In confidential polling reception, the specified confidential box number was not registered in the destination.
E03500 or U03500Fax Communication Error: In interoffice subaddress-based bulletin board reception, the specified subaddress confidential box number was not registered in the destination unit.
E03500 or U03500Fax Communication Error: The destination was being accessed.
E03600 or U03600Fax Communication Error: Confidential polling reception was interrupted because of a mismatch in specified confidential box numbers.
E03600 or U03600Fax Communication Error: An interoffice subaddress-based bulletin board reception was interrupted because of a mismatch in the specified subaddress confidential box number.
E03700 or U03700Fax Communication Error: Confidential polling reception failed because the destination unit had no confidential polling transmission capability or data was not accumulated in any box in the destination unit.
E03700 or U03700Fax Communication Error: Interoffice subaddress-based bulletin board reception failed because the destination unit had no subaddress-based bulletin board transmission capability, or data was not stored in any subaddress confidental box in the destination unit.
E04000 or U04000Fax Communication Error: The confidential box specified for confidential transmission was not registered in the destination unit.
E04000 or U04000Fax Communication Error: In interoffice subaddress-based transmission mode, the specified subaddress box number was not registered in the destination unit.
E04000 or U04000Fax Communication Error: The destination was being accessed.
E04100 or U04100Fax Communication Error: Confidential transmission failed because the destination unit had no confidential capability.
E04100 or U04100Fax Communication Error: Subaddress-based transmission failed because the destination unit had no subaddress-based reception capability.
E04200 or U04200Fax Communication Error: In encrypted tranmission, the specified encryption box was not registered in the destination unit.
E04300 or U04300Fax Communication Error: Encrypted transmission failed because the destination unit had no encrypted communication capability.
E04400 or U04400Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted transmission. Encryption keys did not agree.
E04401 or U04401Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted trasmission. The encryption key was not registered.
E04500 or U04500Fax Communication Error: Encrypted reception was interrupted because of a mismatch in ecryption keys.
E05000 or U05000Fax Communication Error: In transmission with a specified number, the set number of originals was different from the number of transmitted originals.
E05100 or U05100Fax Communication Error: Password check transmission or restricted transmission was interrupted because the permit ID numbers did not match.
E05200 or U05200Fax Communication Error: Password check reception or restricted reception was interrupted because the permit ID numbers did not match, the rejected fax numbers did match, or the destination receiver did not return its phone number.
E05300 or U05300Fax Communication Error: Password check reception or restricted reception was interrupted because the permitted numbers did not match, the rejected numbers did match, or the machine in question did not acknowledge its phone number.
E09000 or U09000Fax Communication Error: G3 communication was attempted but failed because the destination unit was a G2 machine.
E12000 or U12000Fax Communication Error: Relay broadcast was requested from a command station but memory overflowed during reception.
E12000 or U12000Fax Communication Error: In subaddress-based relay reception memory overflowed.
E12100 or U12100Fax Communication Error: Relay was commanded but memory overflowed in the destination unit (relay station).
E14000 or U14000Fax Communication Error: Memory overflowed during confidential reception.
E14000 or U14000Fax Communication Error: Memory overflowed in subaddress-based confidential reception.
E14100 or U14100Fax Communication Error: Memory overflowed in the destination unit during confidential transmission.
E14100 or U14100Fax Communication Error: Memory overflowed in the destination unit during interoffice subaddress-based transmission.
E19000 or U19000Fax Communication Error: Memory overflowed during memory reception.
E19100 or U19100Fax Communication Error: Memory overflowed in the destination unit during transmission.
E19200 or U19200Fax Communication Error: Memory transmission failed because a decoding error occurred.
E19300 or U19300Fax Communication Error: Transmission failed because an error occurred during JBIG encoding.
E19400 or U19400Fax Communication Error: Reception failed because an error occurred during JBIG encoding.
Send SMB Error 1102Error: Username/Password or Shared Name/Folder Name. Domain name is not entered.
Send SMB Error 1102Error: Username/Password or Shared Name/Folder Name. Assign disable user/password.
Send SMB Error 1102Error: Username/Password or Shared Name/Folder Name. Assign the user who is not allowed to access the folder.
Send SMB Error 1102Error: Username/Password or Shared Name/Folder Name. Assign disable shared name.
Send SMB Error 1102Error: Username/Password or Shared Name/Folder Name. Host name error.
Send SMB Error 1103Error: Pathname or File Name. Domain name is not entered.
Send SMB Error 1103Error: Pathname or File Name. Connect to the folder which is not permitted for reference/writing.
Send SMB Error 1103Error: Pathname or File Name. Assign disable folder path.
Send SMB Error 1105Error: Not Supported Protocol. SMB protocol is set to OFF.
Send SMB Error 2101Error: Can Not Connect. Enter the disable host name/IP address.
Send SMB Error 2101Error: Can Not Connect. Assign the wrong port number.
Send SMB Error 2101Error: Can Not Connect. Network is not connected.
Send SMB Error 2103Error: Response Wait With Timeout. The server is unable to communicate.
Send SMB Error 2201Error: Network Transfer. Error occurs on the network.
Send SMB Error 2203Error: Response Wait With Timeout. Response is not returned from the server, above specified time.
Send SMB Error 9181Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
Send FTP Error 1101Error: Host Name. Enter the disable host name/IP address.
Send FTP Error 1102Error: Username/Password. Domain name is not entered.
Send FTP Error 1102Error: Username/Password. Assign disable user/password.
Send FTP Error 1103Error: Pathname or File Name. Connect to the folder which is not permitted for reference/writing.
Send FTP Error 1103Error: Pathname or File Name. Assign disable folder path.
Send FTP Error 1105Error: Not Supported Protocol. FTP protocol is set to OFF.
Send FTP Error 2101Error: Can Not Connect. Enter the disable host name/IP address.
Send FTP Error 2101Error: Can Not Connect. Assign the wrong port number.
Send FTP Error 2101Error: Can Not Connect. Network is not connected.
Send FTP Error 2102Error: Cannot Connect With Timeout. The server is unable to communicate.
Send FTP Error 2102Error: Cannot Connect With Timeout. Send the server which does not support FTP server.
Send FTP Error 2103Error: Response Wait With Timeout. The server is unable to communicate.
Send FTP Error 2201Error: Network Transfer. Error occurs on the network.
Send FTP Error 2202Error: Network Transfer With Timeout. Error occurs on the network.
Send FTP Error 2203Error: Response Wait With Timeout. Response is not returned from the server, above specified time.
Send FTP Error 3101Error: Server Response. The server is error status.
Send FTP Error 9181Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
Send email Error 1101Error: Host Name. SMTP server name is not set. Error SMTP server name.
Send email Error 1102Error: Username/Password. User ID for the authentication is not entered or entered wrongly. Wrong authentication password is entered.
Send email Error 1104Error: No Recipient Address. The destination address is not specified.
Send email Error 1105Error: Not Supported Protocol. SMTP protocol is set to OFF.
Send email Error 1106Error: No Sender Info. Sender address is not entered.
Send email Error 2101Error: Can Not Connect. Select [Other Authenticate] when authenticating POP before SMTP.
Send email Error 2101Error: Can Not Connect. The specified server is not SMTP server.
Send email Error 2101Error: Can Not Connect. Network is not connected.
Send email Error 2102Error: Cannot Connect With Timeout. The server is unable to communicate.
Send email Error 2103Error: Response Wait With Timeout. The server is unable to communicate.
Send email Error 2201Error: Network Transfer. Error occurs on the network.
Send email Error 2202Error: Network Transfer With Timeout. Error occurs on the network.
Send email Error 2203Error: Response Wait With Timeout. Response is not returned from the server, above specified time.
Send email Error 2204Error: Email Size Limit. The size of the email attachment exceeds its limit.
Send email Error 3101Error: Server Response. The server is error status.
Send email Error 3101Error: Server Response. Server setting is not authenticated normally.
Send email Error 3201Error: Not Found Authentication Mechanism. Unsupported SMTP Authentication Mechanism is found.
Send email Error 9181Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
TWAIN Error 2202Error: Network Transfer With Timeout. Response is not returned from the server, above the specified time.
TWAIN Error 9181Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
Software Error 5101Error: Not Yet Connected. Operation handle error. Error for stored status in the operation handle.
Software Error 5102Error: Already Connected. Operation handle error. Error for stored status in the operation handle.
Software Error 5103Error: Not Yet Opened. Error for storage status in the operation handle.
Software Error 5104Error: Already Opened. Error for storage status in the operation handle.
Software Error 7101Error: Memory Allocation. Insufficient memory space.
Software Error 7102Error: Socket Create. Unable to create a communication socket.
Software Error 720fError: Unknown Error. Unable to determine the cause.
Send error. Job is cancelled. Press [End]. 1101Send Email Error: Host Name. SMTP server name is not set. Error SMTP server name.
Send error. Job is cancelled. Press [End]. 1101Send FTP Error: Host Name. Enter the disable host name/IP address.
Send error. Job is cancelled. Press [End]. 1102Send Email Error: Username/Password. User ID for the authentication is not entered or entered wrongly. Wrong authentication password is entered.
Send error. Job is cancelled. Press [End]. 1102Send SMB/FTP Error: Username/Password or Shared Name/Folder Name. Domain name is not entered.
Send error. Job is cancelled. Press [End]. 1102Send SMB/FTP Error: Username/Password or Shared Name/Folder Name. Assign disable user/password.
Send error. Job is cancelled. Press [End]. 1102Send SMB Error: Username/Password or Shared Name/Folder Name. Assign disable shared name.
Send error. Job is cancelled. Press [End]. 1102Send SMB Error: Username/Password or Shared Name/Folder Name. Host name error.
Send error. Job is cancelled. Press [End]. 1103Send SMB/FTP Error: Pathname or File Name. Domain name is not entered.
Send error. Job is cancelled. Press [End]. 1103Send SMB/FTP Error: Pathname or File Name. Connect to the folder which is not permitted for reference/writing.
Send error. Job is cancelled. Press [End]. 1103Send SMB/FTP Error: Pathname or File Name. Assign disable folder path.
Send error. Job is cancelled. Press [End]. 1104Send Email Error: No Recipient Address. The destination address is not specified.
Send error. Job is cancelled. Press [End]. 1105Send Email Error: Not Supported Protocol. SMTP protocol is set to OFF.
Send error. Job is cancelled. Press [End]. 1105Send SMB Error: Not Supported Protocol. SMB protocol is set to OFF.
Send error. Job is cancelled. Press [End]. 1105Send FTP Error: Not Supported Protocol. FTP protocol is set to OFF.
Send error. Job is cancelled. Press [End]. 1106Send Email Error: No Sender Info. Sender address is not entered.
Send error. Job is cancelled. Press [End]. 2101Send Email Error: Can Not Connect. Network is not connected.
Send error. Job is cancelled. Press [End]. 2101Send Email Error: Can Not Connect. Select [Other Authenticate] when authenticating POP before SMTP.
Send error. Job is cancelled. Press [End]. 2101Send Email Error: Can Not Connect. The specified server is not SMTP server.
Send error. Job is cancelled. Press [End]. 2101Send SMB/FTP Error: Can Not Connect. Enter the disable host name/IP address.
Send error. Job is cancelled. Press [End]. 2101Send SMB/FTP Error: Can Not Connect. Assign the wrong port number.
Send error. Job is cancelled. Press [End]. 2101Send SMB/FTP Error: Can Not Connect. Network is not connected.
Send error. Job is cancelled. Press [End]. 2102Send Email/ FTP Error: Cannot Connect With Timeout. The server is unable to communicate.
Send error. Job is cancelled. Press [End]. 2102Send FTP Error: Cannot Connect With Timeout. Send the server which does not support FTP server.
Send error. Job is cancelled. Press [End]. 2103Send Email/ SMB/ FTP Error: Response Wait With Timeout. The server is unable to communicate.
Send error. Job is cancelled. Press [End]. 2201Send Email/ SMB/ FTP Error: Network Transfer. Error occurs on the network.
Send error. Job is cancelled. Press [End]. 2202Send Email/FTP Error: Network Transfer With Timeout. Error occurs on the network.
Send error. Job is cancelled. Press [End]. 2202Send TWAIN Error: Network Transfer With Timeout. Response is not returned from the server, above the specified time.
Send error. Job is cancelled. Press [End]. 2203Send Email/FTP Error: Response Wait With Timeout. Response is not returned from the server, above specified time.
Send error. Job is cancelled. Press [End]. 2204Send Email Error: Email Size Limit. The size of the email attachment exceeds its limit.
Send error. Job is cancelled. Press [End]. 3101Send Email/FTP Error: Server Response. The server is error status.
Send error. Job is cancelled. Press [End]. 3101Send Email Error: Server Response. Server setting is not authenticated normally.
Send error. Job is cancelled. Press [End]. 3201Send Email Error: Not Found Authentication Mechanism. Unsupported SMTP Authentication Mechanism is found.
Send error. Job is cancelled. Press [End]. 5101Send Software Error: Not Yet Connected. Operation handle error. Error for stored status in the operation handle.
Send error. Job is cancelled. Press [End]. 5102Send Software Error: Already Connected. Operation handle error. Error for stored status in the operation handle.
Send error. Job is cancelled. Press [End]. 5103Send SoftwareError: Not Yet Opened. Error for storage status in the operation handle.
Send error. Job is cancelled. Press [End]. 5104Send Software Error: Already Opened. Error for storage status in the operation handle.
Send error. Job is cancelled. Press [End]. 7102Send Software Error: Socket Create. Unable to create a communication socket.
Send error. Job is cancelled. Press [End]. 720fSend Software Error: Unknown Error. Unable to determine the cause.
Send error. Job is cancelled. Press [End]. 9181Send Email/ SMB/ FTP/ TWAIN Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
“Acceptable staple count exceeded.”Is the acceptable staple count exceeded?
“Add paper in cassette #.”Is the indicated cassette out of paper?
“Add paper in MP tray.”Is the paper of the specified size loaded in the multipurpose tray?
“Add staples.”Has the document finisher run out of staples?
“Add toner.”
“An error has occurred.”An internal error has occurred.Make a note of the error code number displayed on the panel. See above.
“Box Limit Exceeded.”Document Box is full, and no further storage is available; Job is cancelled. Repeat Copy Box is full, and no further repeat copy is available.
“Cannot connect to Authentication Server.”
“Cannot duplex print on this paper.”Did you select a paper size/type that cannot be duplex printed?
“Cannot execute this job.”Job is restricted by Job Accounting.
“Cannot offset this paper.”Did you select a paper size that cannot be offset (A3, B4, A5R, B6R, Folio, Ledger, Statement, & 8K)?
“Cannot punch this paper type.”Did you select a paper size/type that cannot be punched?
“Cannot staple this paper.”Did you select a paper size/type that cannot be stapled?
“Check the cover.”Are any covers open? Does the message indicate which cover is open?
“Check the document processor.”Is the document processor open? Is the top cover of the document processor open?
“Check the finisher.”Is the document finisher set correctly?”
“Clean the slit glass.”Dirt has been identified on the slit glass.
“Empty the punch waste box.”The punch waste box of the 3,000 sheet finisher is full.
“Failed to specify Job Accounting.”Job accounting is not specified in the print driver.
“Failed to store job retention data.”
“Fax box limit exceeded.”Fax box is full, and no further storage is available.
“Finisher tray is full of paper.”Is the acceptable storage capacity exceeded for the document finisher tray?”
“Folding tray is full of paper.”Is the acceptable storage capacity exceeded for the folding tray of the 3,000 sheet document finisher?”
“Hard Disk error. Job is cancelled. Press [End] ##”An error has occurred on the hard disk.
“Incorrect Login User Name or Password.”
“Job Accounting restriction exceeded.”The print count exceeded the acceptable count restricted by Job Accounting.
“Job Separator is full of paper.”Is the maximum capacity of the job separator tray exceeded?
“KPDL error.”A PostScript error has occurred.
“Mailbox tray is full of paper.”
“Memory card error.”Was the memory card (Compact Flash) removed while being accessed? Was a valid memory card inserted?
“Memory card error. Job is cancelled. Press [End]. Code: 01Memory Card Error: Format error.
“Memory card error. Job is cancelled. Press [End]. Code: 04Memory Card Error: Insufficient memory card space to complete this operation.
“Memory is full.”Unable to continue the job, as the memory is used up.”
“Memory Is Low”Logic Lockup
“Paper Jam. ###”Make a note of the jam location number displayed on the panel. Leave the machine On.
“Print overrun.”Warning. Low printer memory.
“Removable memory error.”An error has occurred on the USB stick memory or Compact Flash memory.
“Removable memory was removed.”
“Replace all originals and press [Continue].”
“Replace the waste toner box.”The waste toner box is full.
“Reset all originals in the document processor.”Are there any originals left in the document processor?
“Scanner memory is full.”Scanning cannot be performed due to insufficient memory for the scanner. Is the acceptable scanning count exceeded?
“Scanner Paused”DMA transmission of compressed, ecompressed, rotated, relocated, or blanked-out image data does not complete within a specified period of time.
“Set the folding tray.”Is the folding tray correctly installed to the 3,000 sheet capacity document finisher?
“Set the folding unit.”Is the folding tray correctly installed to the 3,000 sheet capacity document finisher?
“Set the punch waste box.”The waste toner box is not installed correctly.
“Set the waste toner box.”The waste toner box is not installed correctly.
“Staple error.”The location of the jam will be indicated on the panel. Leave the machine On.
“Staple jam.”The location of the jam will be indicated on the panel. Leave the machine On.
“The ID is not registered.”The account ID# does not match.
“The memory card is not formatted.”Is the removable memory formatted by this machine?
“The phone receiver is off the hook.”
“The removable memory is not formatted.”Is the removable memory formatted by this machine?
“The source file is not found.”The specified file is not found.
“Top tray of the machine is full of paper.”The exit tray at the top of the machine is full.
“Tray # is full of paper.”Is the acceptable storage capacity exceeded for any of the output trays A, B, or C of the 3,000 sheet capacity document finisher?
“Warning low memory.”Further scanning cannot be performed due to insufficient memory.




Error CodeDescription
0xF330Component: RIP. Category: RIP. Recovery impossible error (CreatePrint and return back value of API is indirect).
0xF331Component: RIP. Category: RIP. Fail to initialize.
0xF333Component: RIP. Category: RIP. Access failure to ME.
0xF335Component: RIP. Category: RIP. Failure to switch TASK.
0xF336Component: RIP. Category: RIP. IOBL process failure.
0xFB30Component: Panel. Category: KI-Panel. Failed to connect the communication of the controller when starting up. Blue back screen. Cannot enter maintenance mode.
0xFB31Component: Panel. Category: KI-Panel. Refused to connect the communication of the controller when starting up. Blue back screen. Cannot enter maintenance mode.
0xFB32Component: Panel. Category: KI-Panel. Time to start up request command (start up request command could not be received). Blue back screen. Cannot enter maintenance mode.
0xFB33Component: Panel. Category: KI-Panel. Cut off of the communication with the controller is detected – waiting to receive: select () OK return, recv() RX data length 0. Blue back screen. Cannot enter maintenance mode.
0xFB34Component: Panel. Category: KI-Panel. Time out for Response telegraphic message (could not receive response telegraphic message within a fixed time). In case on not through httpd, this error occurs (in case it does not become CGI time out).
0xFB35Component: Panel. Category: KI-Panel. Received abusive command from controller. At this moment, only the case that unexpected command comes in when wating for the startup request command.
0xFB36Component: Panel. Category: KI-Panel. Connection error is detected when waiting for he response telegraphic message from the controller. select () function returned the error (other than EINTR).
0xFB37Component: Panel. Category: KI-Panel. Connection error is detected when waiting for he response telegraphic message from the controller. rcv () function returned the error.
0xFB38Component: Panel. Category: KI-Panel. Communication error is detected when transferring (using UNIX domain) response telegraphic message in the panel. send() function returned the error (other than EINTR).
0xFB39Component: Panel. Category: KI-Panel. Crucial error is detected when processing receive/transfer of the response telegraphic message from controller. Failed to acquire semafo???
0xFB3AComponent: Panel. Category: KI-Panel. Communication error is detected when sending required response telegraphic message from panel. send() function returned the error (other than EINTR).
CF000Component: HDD. Failure to initialize with “dbinit, hostif_stat_chg” comand.
CF000Operation panel PWB comunication error.
CF010ROM Checksum Error.
CF010Main PWB Checksum Error/System Error. Communication error between panel and main controller.
CF012ROM Checksum Error.
CF020Memory Checksum Error/Operation System Error.
CF030Main PWB System Error.
CF040Engine PWB Communication Error.
CF040Engine PWB Communication Error.
CF041Scanner PWB Communication Error.
CF050Engine ROM Checksum Error.
CF060Engine RAM Error.
CF070Flash ROM Error. Defective flash ROM (which?).
CF080Flash ROM Error (during download). Defective flash ROM (which?).
CF090Fax System M Communication Error.
CF125Scanner Unit Error
CF131Component: PCM. Category: OS. Failure to initialize with “dbinit, hostif_stat_chg” comand.
CF131Component: PCM. Category: OS. Failure to acquire Entity data with “dbinit, hostif_stat_chg” comand.
CF145Fax Unit Error.
CF14FPower Source Secondary Side Error/Operation System Error. The operation decomes unstable after recovering the power supply fail (brownout or power drop). Wall voltage is unstable or the main power supply switch was turned OFF/ON within 1 sec.
CF14FComponent: OS. Category: OS. Primary supply voltage dropped off temporarily and recovery operation was not stable. If the input power supply voltage is not stable of the Main SW is turned Off/On quickly (about 1 second), this problem occurs.
CF186Print Unit: DVU_PRT_SYSERR_F226_ERROR (Video data flushing error)
CF18AEngine Firmware Incompatible.
CF18CDocument BOX error.
CF1FFComponent: ScanSys. Category: ScanSys. When the scanner scanning parameter from the topside is in error.
CF1FFComponent: IPLogical. Category: PrintSystem. Could not obtain instance of Config, SystemStatus. Use below mentioned class: ipl_search_output.cpp, ipl_feeder_spec.cpp, outputcheck.cpp.
CF1FFComponent: Machine Configuration. Category: PrintSystem. Could not obtain instance of Config, SystemStatus. Use below mentioned class: machine_status_engine.cpp.
CF1FFComponent: OutputMission. Category: PrintSystem. Increasing and decreasing “Lib”, in case that even if there is no original available, tried to process increasing & decreasing.
CF1FFComponent: OutputMission. Category: PrintSystem. In case to specify some other value (indirect value) other than single sided/duplex/forced duplex for increasing & decreasing “Lib”.
CF1FFComponent: OutputMission. Category: PrintSystem. In case of the address for Job setting value structure is NULL.
CF1FFComponent: OutputMission. Category: PrintSystem. In case of the code for output completion notice is indirect.
CF1FFComponent: OutputMission. Category: PrintSystem. When writing the original information to the storage, in case to get the reply back as [Other Error].
CF1FFComponent: OutputMission. Category: PrintSystem. In case to get the reply as [Finisher out of order Error], [No Feeder available in search] from Paper feed/eject “Lib”.
CF1FFComponent: OutputMission. Category: PrintSystem. In case to get the reply as failure from rotation calculation “Lib”.
CF1FFComponent: PrintSystem. Category: PrintSystem. Could not obtain instance of Config, SystemStatus. Use below mentioned class: print_startup.cpp.
CF1FFComponent: SVI. Category: LioPanel. Logical Error (In case of given parameter is NULL).
CF214Codec: GICL_CDC_ERR_FACTOR_JPEG (several hardware error, software error).
CF215Codec: GICL_CDC_ERR_FACTOR_SRLE (several hardware error, software error).
CF234Data conversion error.
CF235Error code when receiving/printing email.
CF245Process Manager: SYS_PRCM_ERR_FACTOR_SVC_PROC_DOWN (Device process down).
CF246Process Manager: SYS_PRCM_ERR_FACTOR_DEV_PROC_DOWN (Device process down).
CF247Process Manager: SYS_PRCM_ERR_FACTOR_JOBIMG_PROC_DOWN (Job image process down).
CF247Component: ScanSys. Category: ScanSys. Library Error inside of ScanSys.
CF248Component: UNKNOWN. Category: UNKNOWN.
CF248Component: UNKNOWN. Category: UNKNOWN. Code present on with Kyocera Barfode Font CF card installed.
CF248Process Manager: SYS_PRCM_ERR_FACTOR_PRN_PROC_DOWN (Printer process down).
CF256Fax System M IOBL error or KUIOLIB error. Poor contact at the fax card card due to mis-installation.
CF257Component: LFM. Category: FaxSys. KUIOLIB error. Poor contact at the fax card card due to mis-installation.
CF257Fax System M IOBL error or KUIOLIB error. Poor contact at the fax card card due to mis-installation.
CF25ENetwork Manager:
CF25FComponent: LFM. Category: FaxSys. Instance Check Error, Paramemter Error from topside.
CF26FComponent: PrintSys. Category: PrintSys. It occurs when the error noticed from VideoDriver. Use by Video_Driver class: Function name, factor can be found by the detail code.
CF26FPrint System Other Errors. Bug of v.2.03B has been fixed by v. 2.04A (Booklet > Booklet Print).
CF26FSystem State Manager:
CF278Energy Saving Manager:
CF320Component: LioFax. Category: FaxSys. An Observer Deletion Error occurred during salvage process. Error received from the method on EventManager or message Tx.
CF321Component: LioFax. Category: FaxSys. Segment code for LioFax initialization is different from “03KH”.
CF323Component: LioFax. Category: FaxSys. Return address of Page class when doing FAX Tx/Rx is other abnormal error. Entity (Config, BOX, etc.) access error.
CF324Component: LioFax. Category: FaxSys. Entity parameter error.
CF325Component: LioFax. Category: FaxSys. In case that the time when Error came back from LFM.
CF326Component: LioFax. Category: FaxSys. IOBL error.
CF327Component: LioFax. Category: FaxSys. At the time of KUIOLIB error, CodeChange error, FaxLib error (Sender recorde, Entity related error).
CF32FComponent: LioFax. Category: FaxSys. Instance Check Error. Parameter Error from topside.
CF337Device Error (scan control):
CF3FFComponent: RIP. Category: RIP. Other/System Crucial Error.
CF423Component: FaxJOB. Category: FaxSys. As the error came back at IF for DocumentBox, JobInfo, Config Entity.
CF423Component: FaxJob. Category: FaxSys. The error came back when accessing (obtaining data, setting data) to below Entity related: job_ent(JobModel,JobInfo), config_ent, reservation, account(certificate), document_box.
CF423Fax System M Error. Wrong data or value detected when the following function is used. Or poor contact at fax card due to mis-installation.
CF423Fax System M Error. The IF error detects during system authentication from ACT_Account_Manager. Or poor contact at fax card due to mis-installation.
CF424Component: FaxJob. Category: FaxSys. As the error came back when obtaining IF for system authentication from ACT_Account_Manager.
CF424Component: FaxJob. Category: FaxSys. The date obtained from the below Entity related is unexpected data: job_ent(JobInfo).
CF427Component: FaxJob. Category: FaxSys. The error came back for the IF of LioFax observer addition/deletion.
CF42FComponent: FaxJob. Category: FaxSys. As handing over of the NULL pointer in the class occurred. As memory reservation with new in heap domain is failed: Assert for preventing from segment drop off.
CF42FComponent: FaxJob. Category: FaxSys. When generating the class, fail new at obtaining data domain, soft logic error (software bug).
CF433Component: NetClient. Category: ImageProcess. Entity Error.
CF434Component: NetClient. Category: ImageProcess. Entity Data Invalid.
CF437Component: NetClient. Category: ImageProcess. Other Library Error (ImageLibrary, PageData, EventManager).
CF43FComponent: NetClient. Category: ImageProcess. Crucial (no memory, invalid parameter, etc.).
CF441Component: CreateScan. Category: ImageProcess. Initialize Error.
CF444Component: CreateScan. Category: ImageProcess. Entity Data Invalid.
CF445Component: CreateScan. Category: ImageProcess. Middleware Error (LioScanner error).
CF451Component: CreatePrint. Category: ImageProcess. Initialization Error.
CF433 CF434 CF437 CF43F CF441 CF444 CF445 CF451HDD Image Process Error. Destruction of stored jobs on the HDD. It may occur when selecting the keys for calling stored copy or scanner job from a custom box.
CF453Component: CreatePrint. Category: ImageProcess. Entity Error.
CF454Component: CreatePrint. Category: ImageProcess. Entity Data Mismatch.
CF45FComponent: CreatePrint. Category: ImageProcess. Other Error.
CF460Component: CreateBox (Memory Tx). Category: ImageProcess. Unrecoverable Error.
CF463Component: CreateBox (Memory Tx). Category: ImageProcess. Entity Error.
CF46FComponent: CreateBox (Memory Tx). Category: ImageProcess. Crucial (no memory, invalid parameter, etc.).
CF46FPDL Interpreter: REN_INT_ERR_FACTOR_GENERAL (other general error).
CF470Component: CreateFax. Category: ImageProcess. Unrecoverable Error.
CF473Component: CreateFax. Category: ImageProcess. Entity Error.
CF47FComponent: CreateFax. Category: ImageProcess. Crucial (no memory, invalid parameter, etc.).
CF484Component: Edit. Category: ImageProcess. Data Invalid (PageData).
CF487Component: Edit. Category: ImageProcess. Other Library Error (ImageLibrary).
CF48FComponent: Edit. Category: ImageProcess. Crucial.
CF490Component: Output(Fax). Category: ImageProcess. Unrecoverable Error.
CF493Component: Output(Fax). Category: ImageProcess. Entity Error.
CF494Component: Output(Fax). Category: ImageProcess. Entity Data Invalid.
CF45F CF453 CF454 CF45F CF460 CF463 CF46F CF470 CF473 CF47F CF484 CF487 CF48F CF490 CF493 CF494HDD Image Process Error. Destruction of stored jobs on the HDD. It may occur when selecting the keys for calling stored copy or scanner job from a custom box.
CF515
CF526System Error:
CF528Component: SVI. Category: LioPanel. Panel data abusion error.
CF530Component: PJL. Category: RIP. Recovery impossible error: Thread Create failed.
CF530Component: ReportEventService. Category: RIP. Recovery impossible error: Thread Create failed.
CF530Component: SVCTL_FaxRx_Event_Control. Category: KI Sc. As failed to obtain EM_FaxRx_Ec_Event_Fax_Enable.
CF530Component: SVCTL_Reservation_Event_Control. Category: KI Sc. As failed to notice the event for EM_Rsv_EC_op_Event_FaxJob_Ready.
CF530Component: SVCTL_Job_Start_Command. As JobInfo giving to JSM_JobServiceManager is NULL.
CF533Component: PJL. Category: RIP. Entity error: when CLITICAL ERROR occurred at ME access.
CF533Component: ReportEventService. Category: RIP. Entity error: when CLITICAL ERROR occurred at ME access.
CF551Component: MLPRN. Category: NetAppl. Task generation error.
CF551Component: MLPRT. Category: NetAppl. Task generation error.
CF551Component: EVR_LGS. Category: NetAppl. Task generation error.
CF610Component: SSTUP. Category: OS. Error in the SystemStartUp (Thread generation, Entity data acquisition, DiskManager operation).
CF610Undefined.
CF610System Start Error.
CF615Report Page Generator: USV_RPG_ERR_FACTOR_STREAM (Stream access error).
CF620Component: EventManager. Category: KM-Entity. Failed to obtain/receive event from framework.
CF620Unable to Print.
CF620System Error. Error acquiring the event data. Panel detects CF000 as same error.
CF620System Error. Error acquiring the event data. Panel detects CF000 as same error. Unable to Load Files To CF Card.
CF630Component: PowerManagement. Category: OS. Failed to mount or unmount during transition of the condition.
CF710Component: IIS. Category: NetApl. Network file written error (inetd).
CF713Component: IIS. Category: NetApl. Entity error (inetd).
CF720Component: IIS. Category: NetApl. Network file written error (services).
CF723Component: IIS. Category: NetApl. Entity error (services).
CF730Component: IIS. Category: NetApl. Network file written error (snmpd).
CF733Component: IIS. Category: NetApl. Entity error (snmpd).
CF743Component: IIS. Category: NetApl. Entity error (hosts allow).
CF750Component: IIS. Category: NetApl. Network file written error (hostname).
CF753Component: IIS. Category: NetApl. Entity error (hostname).
CF760Component: IIS. Category: NetApl. Network file written error (papd).
CF763Component: IIS. Category: NetApl. Entity error (papd).
CF770Component: IIS. Category: NetApl. Network file written error (cups).
CF773Component: IIS. Category: NetApl. Entity error (cups).
CF780Component: IIS. Category: NetApl. Network file written error (dhcclient).
CF783Component: IIS. Category: NetApl. Entity error (dhcclient).
CF790Component: IIS. Category: NetApl. Network file written error (smb).
CF793Component: IIS. Category: NetApl. Entity error (smb).
CF7A0Component: IIS. Category: NetApl. Network file written error (netware).
CF7A3Component: IIS. Category: NetApl. Entity error (netware).
CF7B0Component: IIS. Category: NetApl. Network file written error (ipfilter).
CF7B3Component: IIS. Category: NetApl. Entity error (ipfilter).
CF7C0Component: IIS. Category: NetApl. Network file written error (ethermode).
CF7C3Component: IIS. Category: NetApl. Entity error (ethermode).
CF7D0Component: IIS. Category: NetApl. Network file written error (other).
CF7D3Component: IIS. Category: NetApl. Entity error (other).
CF7D7Readout Error of SSL (authentication data).
CFAxxHDD Error.
CFAxxHDD Error.
CFA10Component: OS_TOOLS. Category: OS. Error inside of hot plug detection thread, overwritten thread (failed to issue the event, failed to operate signal handler).
CFA20Component: OS_TOOLS. Category: OS. Failed to obtain memory size.
CFA23Component: OS_TOOLS. Category: OS. Access error to the Entity at master data stored area component.
CFA30Component: OS_TOOLS. Category: OS. CF-DETECT OPEN error <0x07>.
CFA30Component: OS_TOOLS. Category: OS. CF-DETECT IOCTL error <0x08>.
CFA30Component: OS_TOOLS. Category: OS. CF-DETECT CLOSE error <0x09>.
CFA30Component: OS_TOOLS. Category: OS. AES conversion OPEN error <0x0a>.
CFA30Component: OS_TOOLS. Category: OS. AES conversion IOCTL error <0x0b>.
CFA30Component: OS_TOOLS. Category: OS. AES conversion CLOSE error <0x0c>.
CFA30Component: OS_TOOLS. Category: OS. AES conversion command return value error <0x0d>.
CFA30Component: OS_TOOLS. Category: OS. Message queue creation error <0x15>.
CFA30Component: OS_TOOLS. Category: OS. Message queue Tx error <0x16>.
CFA30Component: OS_TOOLS. Category: OS. Message queue Rx error <0x17>.
CFA30Component: OS_TOOLS. Category: OS. Message queue deletion error <0x18>.
CFA37Component: OS_TOOLS. Category: OS. Event Tx error <0x19>.
CFA43Component: OS_TOOLS. Category: OS. Access error to the Entity at USB activation component.
CFB00Component: Panel. Category: KI-Panel. Netfront error (SLIM_E_GENERIC).
CFB01Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_DNS_INVAL).
CFB02Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_DNS_NOSERVER).
CFB03Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_DNS_TIMEDOUT).
CFB04Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_DNS_NOTFOUND).
CFB05Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_TCP_OPEN).
CFB06Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_TCP_CONNECT).
CFB07Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_TCP_READ).
CFB08Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_TCP_WRITE).
CFB09Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_SSL_CONNECT).
CFB0AComponent: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_SSL_HANDSHAKE).
CFB0BComponent: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_SSL_READ).
CFB0CComponent: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_SSL_WRITE).
CFB0DComponent: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REQTIMEDOUT).
CFB0EComponent: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_RSPTIMEDOUT).
CFB0FComponent: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_CACHE_NONE).
CFB10Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_CACHE_EXPIRE).
CFB11Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_AUTH_UNKNOWN).
CFB12Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_AUTH_NOHEADER).
CFB13Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_AUTH_FORMAT).
CFB14Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REDIRECT_FORMAT).
CFB15Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REDIRECT_CANCELLED).
CFB16Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REQ_HEADER_SIZEOVER).
CFB17Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REQ_BODY_SIZEOVER).
CFB18Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_RSP_HEADER_SIZEOVER).
CFB19Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REQ_TOOMANYCONTINUE).
CFB1AComponent: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_TLS_INTOLERANT).
CFB1BComponent: Panel. Category: KI-Panel. Netfront error (SLIM_FILEP_E_OPEN).
CFB1CComponent: Panel. Category: KI-Panel. Netfront error (SLIM_FILEP_E_READ).
CFB1DComponent: Panel. Category: KI-Panel. Netfront error (SLIM_CONTENT_E_SIZEOVER).
CFB1EComponent: Panel. Category: KI-Panel. Netfront error (SLIM_CONTENT_E_NO_CONTENT).
CFB1FComponent: Panel. Category: KI-Panel. Netfront error (SLIM_CONTENT_E_TOOMANYREDIRECT).
CFB20Component: Panel. Category: KI-Panel. Netfront error (SLIM_CONTENT_E_TOOMANYAUTH).
CFB21Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_NOMEMORY).
CFB22Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_NOMEMORY_IMAGE).
CFB23Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_TOTAL_SIZEOVER).
CFB24Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_BADURL).
CFB25Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_BADMIMETYPE).
CFB26Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_MIXEDSECURETYPE).
CFB27Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_INPUTHISTORY_SIZEOVER).
CFB28Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_INPUT_REQUIRED).
CFB29Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_KMC_NOTIFYMAXWINDOW).
CFB2AComponent: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_KMC_SWKOVERFLOW).
CFB2BComponent: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_KMC_FILEDOWNLOAD).
CFB2CComponent: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_KMC_SEGFAULT).
CFB2C CFB30 CFB31Panel Error. NetFont error. Communication error between panel and main controller during initialization or rejection of communication by controller during initialization. Blue Screen of Death.
CFB30Component: Panel. Category: KI-Panel. Failed to connect the communication of the controller when starting up. Blue back screen. Cannot enter maintenance mode.
CFB30Incompatible Level Of Firmware on Main EEPROM.
CFB30Incompatible Level Of Firmware on Main EEPROM.
CFB31Component: Panel. Category: KI-Panel. Refused to connect the communication of the controller when starting up. Blue back screen. Cannot enter maintenance mode.
CFB31Corrupt Firmware on Main EEPROM.
CFB31Corrupt Firmware on Main EEPROM.
CFB32Component: Panel. Category: KI-Panel. Time to start up request command (start up request command could not be received). Blue back screen. Cannot enter maintenance mode.
CFB32Panel Error. Timeout request for start up command. Start command hasn’t been received. Possible destruction of system file in HDD. Cannot enter maintenance mode. Blue Screen of Death.
CFB33Component: Panel. Category: KI-Panel. Cut off of the communication with the controller is detected – waiting to receive: select () OK return, recv() RX data length 0. Blue back screen. Cannot enter maintenance mode.
CFB33Panel Error. Detects disconnection with controller. Possible overdrive of control board or destruction of system file in HDD. Cannot enter maintenance mode. Blue Screen of Death.
CFB34Component: Panel. Category: KI-Panel. Time out for Response telegraphic message (could not receive response telegraphic message within a fixed time). In case on not through httpd, this error occurs (in case it does not become CGI time out).
CFB35Component: Panel. Category: KI-Panel. Received abusive command from controller. At this moment, only the case that unexpected command comes in when wating for the startup request command.
CFB36Component: Panel. Category: KI-Panel. Connection error is detected when waiting for he response telegraphic message from the controller. select () function returned the error (other than EINTR).
CFB37Component: Panel. Category: KI-Panel. Connection error is detected when waiting for he response telegraphic message from the controller. rcv () function returned the error.
CFB38Component: Panel. Category: KI-Panel. Communication error is detected when transferring (using UNIX domain) response telegraphic message in the panel. send() function returned the error (other than EINTR).
CFB39Component: Panel. Category: KI-Panel. Crucial error is detected when processing receive/transfer of the response telegraphic message from controller. Failed to acquire semafo???
CFB3AComponent: Panel. Category: KI-Panel. Communication error is detected when sending required response telegraphic message from panel. send() function returned the error (other than EINTR).